電磁閥的常見故障與排除
1、電磁閥通電后不工作：檢查電源接線是否不良→重新接線和接插件的連接；檢查電源電壓是否在工作范圍內-→調到正常位置范圍；檢查線圈是否脫焊→重新焊接；線圈短路→更換線圈；工作壓差是否不合適→調整壓差→或更換相稱的電磁閥；流體溫度過高→更換相稱的電磁閥；有雜質使電磁閥的主閥芯和動鐵芯卡死→進行清洗,如有密封損壞應更換密封并安裝過濾器；液體粘度太大,頻率太高和壽命已到→更換產品。
2、電磁閥不能關閉：主閥芯或鐵動芯的密封件已損壞→更換密封件；流體溫度、粘度是否過高→更換對口的電磁閥；有雜質進入電磁閥主閥芯或動鐵芯→進行清洗；彈簧壽命已到或變形→更換；節流孔平衡孔堵塞→及時清洗；工作頻率太高或壽命已到→改選產品或更新產品。
3、其它情況：內泄漏→檢查密封件是否損壞,彈簧是否裝配不良；外泄漏→連接處松動或密封件已壞→緊螺絲或更換密封件；通電時有噪聲→頭子上堅固件松動,擰緊。電壓波動不在允許范圍內，調整好電壓。鐵芯吸合面雜質或不平，及時清洗或更換。
